Hi,欢迎访问北京北广精仪仪器设备有限公司

北京北广精仪仪器设备有限公司

吴堡塑料摩擦系数试验机 批发

联系我们
  • 北京北广精仪仪器设备有限公司
  • 陈丹
热门产品
联系方式
北京北广精仪仪器设备有限公司
  • 联 系 人:陈丹
  • 手 机 号:
  • 公司电话:
  • 公司地址:北京
文章详情

吴堡塑料摩擦系数试验机 批发

发布用户:Bgjy 时间:2021-11-26 09:38

吴堡塑料摩擦系数试验机 批发

吴堡塑料摩擦系数试验机   批发


产品名称:塑料滑动摩擦磨损试验机

型号:M-200 特点:本机采用高精度扭矩传感器,嵌入式中央单元处理系统cpu控制,支持xp  win7. win8.  win10系统,软件实时绘制显示扭矩-时间曲线、摩擦系数-时间曲线,绘制摩擦力、摩擦系数、磨损量等曲线变化,可设定试验次数,显示当前试验次数,设定时间及当前试验时间等多种功能;

本机具有一次设置,全自动运行,实验结束后自动停机,并检测磨损程度;

配有彩色打印机,可以打印出带有曲线,表格数据,试验单位名称等精美的试验报告单。另外本仪器配有故障自动报警系统问题报警灯和软件报警灯同时提示出现问题时间保护仪器以免零件损坏。是各个科研单位,大学,企业实验室的必备检测设备。

吴堡塑料摩擦系数试验机   批发

塑料名称、规格、牌号、生产厂;A. plastic name, specification, brand and manufacturer;

复合材料滑动摩擦磨损试验机  技术参数Technical parameters:  M-200

试验中上转轴保持静止,下转轴以200转/分转动,摩擦副做滑动摩擦,对磨2小时,负荷20公斤,根据材料,允许选择其它负荷.试验环境温度为23±5摄氏度.During the test, the upper shaft remains stationary, the lower shaft rotates at 200 rpm, and the friction pair is subject to sliding friction. For 2 hours, the load is 20kg. Other loads are allowed according to the materials. The test environment temperature is 23 ± 5 ℃.

电源线:接入电源线插口

试验日期、人员。G. test date and personnel.

记录圆环转数的计数器或记时器,精确到1%以内。A counter or chronograph for recording the revolution of a ring, with an accuracy of less than 1%.

试验报告应包括下列内容:The test report shall include the following contents:

复合材料滑动摩擦磨损试验机   本机采用高精度扭矩传感器,16 位单片机电子处理系统,使得本仪器各项测试指标精度非常高。由于集成程度很高,所以设备本身的稳定性极好,本机具有一次设置,全自动运行,实验结束后自动停机,并检测磨损程度,同时通过打印机打印试验数据等功能。是各个科研单位,大学,企业实验室的必备检测设备。

转动速度: 0-200转/分 连续可调到500转/分

记录圆环转数的计数器或记时器,精确到1%以内。A counter or chronograph for recording the revolution of a ring, with an accuracy of less than 1%.

吴堡塑料摩擦系数试验机   批发

电脑一套(联想,双核cpu、2g内存、250g硬盘、2.3主频 19显示屏 win7系统)

此界面可以设置报告名称,试验参数,可以通过勾选参数前边的“对”勾,来决定试验报告中是否打印此项(数据项相同),可能通过勾选“对”勾来确定是否打印,试验参数,试验数据,试验曲线,试验备注等信息。选择完后可通过打印,预览报告,如果满意可以在预览界面通过打印,打出报告。

主要配置:

试样夹具结构和尺寸见图并附配垫圈 4 GB 848-沉头螺钉M3×0.35长10毫米。要保证试样安置后无轴向窜动。See Fig. 2 for the structure and dimension of the sample clamp, with washer 4 GB 848- countersunk screw m3 × 0.35 with length of 10 mm. Ensure that there is no axial movement after the sample is placed.

试验报告可打印试验参数,试验数据,曲线,备注等信息,简单,方便,可编辑。The test report can print experimental parameters, test data, curves, remarks and other information. It is simple, convenient and editable.

计算机控制系统一套;A set of computer control systems;

圆环材质、硬度、光洁度和外径尺寸;D. ring material, hardness, finish and outer diameter;

传动系统,用来带动圆环以给定的转速旋转,精确到5%以内,并要求圆环安装部位轴的径向跳动小于0.01毫米。The transmission system is used to drive the ring to rotate at a given speed, accurate to within 5%, and the radial runout of the shaft at the installation ition of the ring is required to be less than 0.01mm.

试验中上转轴保持静止,下转轴以200转/分转动,摩擦副做滑动摩擦,对磨2小时,负荷20公斤,根据材料,允许选择其它负荷.试验环境温度为23±5摄氏度.During the test, the upper shaft remains stationary, the lower shaft rotates at 200 rpm, and the friction pair is subject to sliding friction. For 2 hours, the load is 20kg. Other loads are allowed according to the materials. The test environment temperature is 23 ± 5 ℃.

标准摩擦环二件;Two standard friction rings;

吴堡塑料摩擦系数试验机   批发

试样的制备方法,摩擦表面状况,测定的试样个数;B. pparation method of sample, friction surface condition, number of samples measured;

高精度扭矩传感器一只;High pcision torque sensor one;

环境温度、温度及状态调节条件;C. environment temperature, temperature and state regulation conditions;

产品合格证一份;A copy of the product certificate;

砝码重量:4KG砝码一件,1KG砝码4件,可实现重量叠加功能。

精度:速度精度≤1%;负荷精度≤0.5%;摩擦力矩精度≤1%;计数器精度≤1S;传感器测量精度≤1accuracy: speed accuracy is less than 1%; load accuracy is less than 0.5%; friction torque accuracy is less than 1%; counter accuracy is less than 1S; sensor measurement accuracy is less than 1%F.

计数器精度:1S

注:试验设备本标准推荐采用M-200型磨损试验机。Note: M-200 wear testing machine is recommended in this standard.

制造标准:GB3960 塑料滑动摩擦磨损试验方法

配件parts:

吴堡塑料摩擦系数试验机   批发

标准磨擦环壹件

摩擦力矩: 0—4N.m;friction torque: 0 - 4N.m;

摩擦力矩精度:1%

试样夹具结构和尺寸见图并附配垫圈 4 GB 848-沉头螺钉M3×0.35长10毫米。要保证试样安置后无轴向窜动。See Fig. 2 for the structure and dimension of the sample clamp, with washer 4 GB 848- countersunk screw m3 × 0.35 with length of 10 mm. Ensure that there is no axial movement after the sample is placed.

试样尺寸: 30mm*7mm*6mm±0.1 mm

高精度扭矩传感器一只;High pcision torque sensor one;

摩擦力矩精度:1%

电源线:接入电源线插口

系统运行稳定,可靠性高。The system runs steadily and has high reliability.

管理:可对使用些设备的用户进行管理。退出:退出操作系统。

吴堡塑料摩擦系数试验机   批发

主机一台(北京北广)

本试验中圆环的材质对塑料磨损试验结果影响很大,因此本标准采用的圆环,其外形尺寸见The material of the ring in this test has a great influence on the plastic wear test results. Therefore, the ring adopted in this standard has the dimensions shown in Figure 材料为45号钢,圆环要求整体淬火,热处理HRC 40~外圆表面光洁度▽倒角处均为0.5×45度,外圆表面与内圆同心度偏差小于0.he material is 45 steel, the ring is required to be quenched as a whole, the heat treatment is HRC 40- the surface finish of the outer circle is ▽ the chamfering is 0.5 × 45 degree, and the concentricity deviation between the outer circle surface and the inner circle is less than 0.    圆环可以反复使用,每次试验后,需重新磨削。当外径小于36毫米就不能再用。作仲裁试验时用直径40毫米的圆环。The ring can be used repeatedly. After each test, it needs to be grinded again. When the outer diameter is less than 36 mm, it can not be reused. A ring with a diameter of 40 mm must be used for the arbitration test.

试验报告Test report

保存:完成试验后可保存试验数据。

试验报告可打印试验参数,试验数据,曲线,备注等信息,简单,方便,可编辑。The test report can print experimental parameters, test data, curves, remarks and other information. It is simple, convenient and editable.

9退出功能: 退出系统。

负荷精度:0.5%

记录圆环转数的计数器或记时器,精确到1%以内。A counter or chronograph for recording the revolution of a ring, with an accuracy of less than 1%.

 北广产品销往上海、广东、河南、浙江、河北、江苏、湖南、内蒙、山东、四川、广州、江西、西北、云南、深圳、吉林、南京、X嘉兴、佛山、苏州、杭州、西安、潥阳、长春、江苏、平顶山、安徽、金水、金华、海南、廊坊、天津、成都、扬州、东莞、济南、南通、株洲、保定、贵州、宜兴、嘉兴、黑龙江、漳州、成都、重庆、咸阳、济南、绍兴、杭州、拉萨、山西、惠州、沧州、江西、沈阳、武汉、沈阳、昆明、南京、鹤山、许昌、青海、宁波、醴陵、淄博、瑞安、阜新、合肥、长沙、常州、瑞安、青岛、北京、济宁、醴陵、厦门、河源、乐清、烟台、福州、龙口、徐州、唐山等地销售。

试样尺寸: 30mm×7mm×6mm; sample size: 30mm x 7mm x 6mm;

吴堡塑料摩擦系数试验机   批发

试样尺寸: 30mm*7mm*6mm±0.1 mm

计算机数据采集卡一块;A piece of computer data acquisition card;

精度:速度精度:1%

管理:可对使用些设备的用户进行管理。退出:退出操作系统。

转动速度: 0-200转/分 连续可调到500转/分

注:圆环材质也可按产品标准另定。Note: the ring material can also be determined according to the product standard.

设定时间及当前试验时间等多种功能,随机配备彩色打印机,可以打印出带有曲线、表格数据等标准要求的试验报告。Set time, current test time and other functions, equipped with color printer, can print out test report with curve, table data and other standard requirements.

使用说明书一份;One copy of the instructions;

试验负荷;E. test load;

传动系统,用来带动圆环以给定的转速旋转,精确到5%以内,并要求圆环安装部位轴的径向跳动小于0.01毫米。The transmission system is used to drive the ring to rotate at a given speed, accurate to within 5%, and the radial runout of the shaft at the installation ition of the ring is required to be less than 0.01mm.

高精度扭矩传感器一只(固尔)

设置:对试验的参数进行设置,如试验速度,试验数据等。 开始:开始进行试验。

吴堡塑料摩擦系数试验机   批发

试验报告应包括下列内容:The test report shall include the following contents:

本试验中圆环的材质对塑料磨损试验结果影响很大,因此本标准采用的圆环,其外形尺寸见The material of the ring in this test has a great influence on the plastic wear test results. Therefore, the ring adopted in this standard has the dimensions shown in Figure 材料为45号钢,圆环要求整体淬火,热处理HRC 40~外圆表面光洁度▽倒角处均为0.5×45度,外圆表面与内圆同心度偏差小于0.he material is 45 steel, the ring is required to be quenched as a whole, the heat treatment is HRC 40- the surface finish of the outer circle is ▽ the chamfering is 0.5 × 45 degree, and the concentricity deviation between the outer circle surface and the inner circle is less than 0.    圆环可以反复使用,每次试验后,需重新磨削。当外径小于36毫米就不能再用。作仲裁试验时用直径40毫米的圆环。The ring can be used repeatedly. After each test, it needs to be grinded again. When the outer diameter is less than 36 mm, it can not be reused. A ring with a diameter of 40 mm must be used for the arbitration test.

计 数 器: 0-9999小时

试验主机一台;Test host one;

采用高精度电机、驱动机、传感器,精度高。using high pcision motor, drive and sensor, high accuracy.

注:试验设备本标准推荐采用M-200型磨损试验机。Note: M-200 wear testing machine is recommended in this standard.

计 数 器: 0-9999小时

电源线:接入电源线插口

标准磨擦环壹件

注:圆环材质也可按产品标准另定。Note: the ring material can also be determined according to the product standard.

吴堡塑料摩擦系数试验机   批发

热点新闻